- 4 leaf barndoors for Junior Fresnel 1000W
- Used to control and shape the light beam
- Heat resistant and treated against rust
HMI PAR 575 watts kit
- Power: 575W
- Daylight-balanced (6000K) spotlight
- Single ended line of Metal-Halide lamps (HMI*)
- Front UV protective glass with safety wire mesh
- Optional spread lenses for beam angle variations
- Sturdy die cast aluminum construction
- Includes: ballast, power cable, barndoors, case
- DMX512 control optional
€3'39900
Available only on pre-order with delivery time of 8-12 weeks.
Powerful daylight-balanced light source
The Cinelight PAR HMI lights are best suited for motion picture, events and TV productions where the maximum light output is required. PAR fixtures are recommended to be used for lighting background elements or diffused / bounced into a white reflector panel to act as a soft fill light for talents (PAR lamps are too hard sources to be used for lighting faces directly).
Optional spread lenses for beam angle variations
The Cinelight PAR HMI lights come with clear, UV protective glass in front topped up by a safety wire mesh. Optional drop-in spreader lenses can be used to fine-tune the light output from wide flood to narrow spot variations, in order to obtain the optimal beam angle. The spreader lenses affect both the shape and angle of the beam and are available to be purchased separately.
Fully die cast aluminum housing
The Cinelight PAR HMI is using a series of aluminum extrusions and aluminum corrosion castings for the housing to quickly dissipate the heat that comes from the light bulb, therefore increasing the lamp's life. The amount of time needed for the fixture to cool down is reduced so it's easier to handle.
High speed & flicker-free HMI ballast
As with any HMI fixture, the Cinelight HMI PAR lights require a ballast in order to function. The Cinelight HMI electronic ballast complies to the industry's high demanding requirements: flicker free, very low noise, high output and stable long-term operation. The ballast features a rugged and compact design for easy handling on the field.
The ballast employs the ALF technology (Active Line Filter) which minimizes the power line interference, providing a higher Power Factor for a more efficient power use. This translates to a consistent color temperature and flicker-free dimming, despite power line voltage fluctuations.
The dedicated high-speed function of the ballast drives the lamp to 300Hz or 1kHz to ensure a flicker-free image in slow motion shootings.
The ON/OFF power switch on the ballast control panel allows for hot re-striking, while the dedicated dimming knob vary the power down to 50%.
Safety circuits such as over-voltage, over-temperature and short-circuit protection provide a safe and reliable operation.
Wide range of applications in the film industry
These lighting instruments are commonly used to light large setups at night, giving a little more depth to the scenes, and also in situations requiring a far reaching, intense beam. Whenever punch or bounce light is required on a set, the Cinelight PAR is the optimal solution. The daylight-balanced output provided by the HMI fixtures is an essential artificial lighting source for most productions.
Transport case included
For easy transportation and safe storage, a hard plywood case is included which accommodates the kit's components: HMI PAR lamp head, electronic ballast, power cable and metal barndoors.
Available only on pre-order with delivery time of 8-12 weeks.
Specifications
HMI - Fixture
Beam type | spot |
Rated power | 575 watts |
Lamp type | Single-End |
Lamp socket | G22 |
Color temperature | 6000K |
Lens type | Interchangeable |
Spot-Flood selector type | Mechanical |
Yoke mount | Spigot 28mm pin |
Housing color | Gray & blue |
Housing material | Aluminum |
Lamp head dimensions | 420 x 290 x 310 cm |
Lamp head weight | 5.6 kg |
HMI - Ballast
Ballast power | 575W / 1200W |
Ballast line power | 1380VA |
Ballast nominal current | 6A-17A |
Ballast operation voltage | 90-265VAC |
Ballast frequency | 50-60 Hz |
Ballast current characteristics | Square wave, 75Hz |
Ballast power factor | 0.98 |
Ballast dimming range | 100%-50% |
Ballast starting | Hot re-strike |
DMX control | Optional |
DMX connectors type | XLR-3P |
ballast power cable length | 7.0 m |
Power cord total length | 3.5 m |
Power connector type | CEE 7/4 - Schuko |
Ballast dimensions | 20 x 29 x 35 cm |
Ballast weight | 9.5 kg |
Ballast protection class | IP22 |
Q & A ( 0 )
Ask a question
Reviews ( 0 )
- Payload: 5 Kg
- Max height: 380 cm | Min height: 130 cm
- 16 mm mounting spigot (5/8" stud)
- Air-cushioned
- Material: aluminum
- Dual-power: 12KWW / 18KW
- MAX lens-less reflector
- HMI 6000K GX51/38 metal-halide lamp
- Electronic Ballast 1KHz flicker free
- Dual wattage ballast 12/18 KW
- Includes barndoors, wheeled EB support
- DMX512 control option
- Opening diameters: 38 mm - 52 mm
- Spigot 28 mm receiver
- Securing bolt for inserted 28 mm stud
- For hanging lights with 28 mm junior stud
- As: LC.465A, LC.4465A, 425151
- Clamp on max pipe diameter 35 mm
- Solid one piece metal body
- Protective rubber coating
- Red color for high visibility
- Power: 180W
- Light output: 18'500 lx @ 1m
- CCT: 5600K | CRI 97 TLCI 98
- Size: 24x18x12 cm | 1.6 kg
- Powerful True-Tone COB LED
- External power controller w/ digital display
- 5 pre-programed lighting effects
- DMX and 2.4GHz wireless remote control
- Bowens type-S mount & light modifiers
- For Junior Fresnel 150W
- Product code: 64502
- Lamp socket: GX6.5
- Power: 150 watts
- Voltage: 230V
- Output: 4000 lm
- Color temperature: 3400K
- Dual wattage head 2500W / 4000W
- Electronic Ballast 1Khz flicker free
- Dual-wattage ballast 2500/4000
- Hot-restrike, PFC
- DMX512 control ballast option
- Wide beam angle up to 125°
- Power: 300W
- Light output: 16200lx (spot) / 5220lx (flood) @ 1m
- Size: 30 x 19 x 16 cm | 2.6 Kg
- Adjustable beam angle from spot 15° to flood 57°
- High quality Fresnel lens with short focal length
- Sturdy die cast aluminum construction
- Optional accessories: scrim kit, filter frame, dimmer
- Converts NP-F batteries to V-Mount
- Converts voltage from 7.2V to 14.4V
- Uses two batteries
- Works with any NP-F type battery